Lexia vs Diagbox vs Peugeot Planet PP2000

This write-up explains what the difference is among Lexia, Diagbox and Peugeot Planet PP2000, which would be a good idea for a total newbie in car diagnostics software that Lexia 3 cable required.
Both Diagbox and PP2000 are used to connect to the car's ECU and carry out diagnostics and manage settings. Which is a better software, however?
Lexia: Citroen, Planet: Peugeot, Diagbox: Citroen & Peugeot
Lexia3 - hardware
Lexia - Software for Citroen
Planet - Software for Peugeot
Diagbox - Front end which contains variations of both of the above
Diagbox is the only one which is still updated.
The hardware is currently on Revision C.
Diagbox: newer, PP2000: quicker
PP2000 and Diagbox are roughly the same thing , Diagbox being the newer software ,
PP2000 is a quicker software but will become obsolete over the next few years as Peugeot will stop using it this year ,
no point in getting PP2000 then having to change to Diagbox
Peugeot Planet: easier and faster
I have planet and also being a newbie installed planet then diagbox they both worked fine though diagbox was a lot slower (you have to start diagbox then choose planet off the option list) so basically if its just for use on your own car then using planet on its own is easier and faster though if your going to attempt using the interface on other vehicles may as well install diagbox with planet and lexia
Lexia + PP200 = Diagbox
lexia is for citreon
planet pp2000 is for peugeot
put both programmes into one software = diagbox
if your going to buy it you might asswell get diagbox which most new interfaces come with anyway.
Both Lexia & PP2000 available within Diagbox
They are the same.... the discs supplied usually contain PP2000 and Diagbox on one disc (PP2000 is also available within the Diagbox installation), and lexia for Citroens on the other. Lexia is also available within Diagbox.
So if you find an interface with rev C, the software discs will contain everything you need and more.
PP2000 on 32-bit, Diagbox on 64-bit
Planet will only run on 32-bit. Diagbox will run on 64-bit, but when you try to call Planet through Diagbox it will crash because it must have 32-bit.
What I do is install VMWare Player (free). Using that, create a virtual machine XP SP3 32-bit (you will need the disk and key). Then install Planet into that. Works well. Sounds very techy, but it is surprisingly easy, because VMWare is so well documented. When installing Planet, do not plug the Lexia interface in to the PC until prompted.
Planet & Diagbox are software Lexia cable required
The Lexia is the cable required to use the software. Only the cable.
To use the cable you will need software as well, Peugeot Planet and Diagbox are the 2 pieces of software to choose from.
Diagbox is much newer software that supports even the latest cars. However I prefer the interface of Peugeot Planet, much easier not to get lost in there.
Generally when you buy a Lexia software will be included on a disk. As to whether it is genuine or not, you should check with the seller before purchase.

How to program Renault Master key easily by FNR key Prog?

This blog will show you how to program a new Renault Master key by  FNR key Prog and Renault true code! €46.99 FNR key Prog 4-in-1 can program key NOT ONLY for Renault, but Ford Nissan!

FNR key Prog Renault key programming steps for Renault Master 2012
Connect FNR key Prog with Renault Master OBD2 port then open FNR key Prog 4-in-1 software.
True code for Renault
Select car model: Master (2008-2013)
Click "Connect to selected vehicle" button.

Follow the software tips, turn on Renault Master hazard light switch. Click "OK".
Make sure car ignition off and key is removed. Click "OK".
Now FNR key Prog will read out programmed key number, key ID and also Renault Master pin code.
Click "Start Program" button to start key programming.

Follow the instruction: insert the new key you want to program, turn car ignition on then click "OK".

Turn ignition off.
Message will show "Do you want to program more keys", click "NO".
Now FNR key Prog successfully add a new key for Renault Master 2012!
You will see "Procedure successful"!

Ktag Firmware 7.020 Review

Here are reviews of Ktag fw v7.020 clone.
(Big thanks to all users’s feedback)
I try with edc16c31 smart 451, read write in bdm ok with ktag, read write ok in obd with kess.
I tested with a lot of edc17 in these day and read and write without problem.
I made a video with a edc17c50 bmw 120d f21 with gpt, read and write ok.
I have a fiat edc17c69 virgin (without software inside), this I can't read.
My Ktag 7.020is able to read and write EDC17C69
7.020 version runs faster and more stable.
Ktag 7.02 good working. no problem.
Ktag master 7.020 displays diagrams via words, not pictures. It’s better to understand0
I tried to read Bosch edc17c69 gpt Fiat 500X and not working, with ktag ori read and write ok.
I read a lot of edc17 and few edc17 with gpt and all read and write ok maybe there is a bug in sw/fw from alientech.
virtual reading is = servidor ALIen.
virtual reading id ecu , and download firmware.
Not real soft.
uds vag =
I compared 7.020 with my old 7.003. KTAG fw 7.020 adds 100+ ECU types and supports new car models e.g. Toyota 76FXXX, PSA 17.4.4, Ford E83, VW 17.5.5 (1766), Mercedes-Benz 276 ECU, Toyota 76F, etc. It should be a good budget i think.
The clone Ktag 7.020 canreadmy 2013 Opel Insignia EDC17C59
I’ve got two versions of ktag 7.020, one with green PCB and the other with blue PCB. No much difference when using both.

How to use OBDSTAR ET-108 USB Inspection Camera with X300 DP?

Is there any Endoscope Inspection Camera to use with OBDSTAR X300 DP?
Yes, check this new tool: OBDSTAR ET-108 USB Inspection Camera. Compatible with both OBDSTAR X300 DP and X300 DP Pad!

How to use OBDSTAR ET-108 with OBDSTAR X300 DP Pad?
First, to enjoy Endoscope function, you should update X300 DP or X300 DP PAD to latest software version.
Take X300 DP as example, after update X300 DP main menu will show "Endoscope" button as below:

Click the "Endoscope" button and choose "Yes" to download the software.

Next, Connect OBDSTAR ET-108 USB Inspection Camera with X300 DP via X300 DP USB connector.

Now, you can use this OBDSTAR ET-108 USB Endoscope Camera!
Compatible with OBDSTAR X300 DP Tablet. (Can also used with other brands' pads in future)
Equip with 6pcs dimmable LED lights
Has 4 kinds probes for choose

OBDSTAR ET-108 Product Parameters list:

OBDSTAR ET-108 Price: €45.99 free shipping
Get more info to know OBDSTAR ET-108 here:
http://www.obd2france.com/wholesale/obdstar-et-108-usb-inspection-camera.html

OBD2France.com all rights reserved, Original Article url:How to use OBDSTAR ET-108 USB Inspection Camera with X300 DP?

How to update XPROG-M V5.0 without dongle to XPROG-M V5.74?

Here is a guide to show how you update XPROG-M V5.0 Box ECU Programmer without dongle to XPROG-M V5.74! Note: You try this method with luck and your own risk.

You also need: ATMEGA64 Repair Chip update XPROG-M

Free download XPROG Box V5.7.4 software:

https://mega.nz/#!PQUzGAKI!LuBfkREVI9vnjPtPKlhdjbv6welC8GkHoZM4Bm9wois

Free download XPROG Box V5.7.4 setup exe:

https://mega.nz/#!vUknWAaZ!VwXXnaREXg4oRFRUYkvmPpkdEyj6ILX4hiEL3obYhMg

XPROG-M V5.0 software update to XPROG-M V5.74 guide

Unzip the XPROG 5.7.4.zip contents to a folder on your desktop.

Open the folder AVRDUDESS and run avrdudess.exe program.

The following procedure will flash the version 5.0 firmware on your XPROG device.

Select your programmer.

Click on “Detect” at the top right corner. It will detect ATMEGA64.

Select your flash file which is in the Firmware folder.

Select your EEPROM file which is in the Firmware folder.

Enable the “Erase flash and EEPROM (-e)” option.

Set the following in the “Fuses & lock bits”

L: 0x2F

H: 0xCA

E: 0xFF

LB: 0x3C

And enable the “Set fuses” and “Set lock” options.

Finally click on “Program” and wait till it finishes and verify all the data are flashed correctly.

If not then try again.

Now that the Xprog has version 5.0 firmware, go to the “XprogDesktop” folder and run “XprogDesktop.exe” file.

Click on “Help->Hardware info…” and once it opens it will ask to upgrade the firmware.

If not, then click on the “Upgrade” button. Once this procedure is finished you can try and read a processor. It will ask for a certificate. If it fails try again.

When it is finished the XPROG will run the latest firmware and you will be able to work with the latest XPROG V5.7.4 software!

Again note that this is not a 100% successful guide, some work and some may not.

If you need 100% tested working latest XPROG-M Programmer that will work almost the same as XPROG-M V5.74, get this one:

XPROG-M V5.70

XPROG-M V5.70 read Freescale MPC55xx

XPROG-M V5.70 read Freescale MPC560x

 

www.obd2france.com all rights reserved, Original Article url:How to update XPROG-M V5.0 without dongle to XPROG-M V5.74

How to install Volvo Vida/Dice on Windows XP VMWare Player

I can confirm that Volvo VIDA 2011A will work in Windows 7 (Ultimate, BTW). But with the following conditions. You need to run IE8 not 9 (I have found that VIDA just won't go with 9), minimum RAM is 2G. Should be good to go with that; but since MSSQL, which VIDA requires is such a hog, other conflicting apps could create issues. Volvo obviously recommends that a VIDA box be used exclusively for that purpose with no other apps installed. Realistically, I have also installed MS Office, Adobe Acrobat and Lightroom, and some Nikon software without creating a problem.

Actually, running a VM is maybe a good solution to avoid collision with other parts of the installed software. As you know, a VM is like a dedicated computer with nothing else installed on it. Another benefit is to use it on your newish computer which is faster (of course VM will steal some performance but I've noticed no problems with VIDA level software which is not a very demanding software)

VM also adds a little more clunkiness on UI having to swing between 2 windowing/operating systems and deal with assigning the mouse+USB inputs between the 2 operating systems. But its not too bad really. Once inside VIDA, one is staying there to work for awhile.

My setup is a 2008ish Macbook Pro (not fast by today's standards) with VirtualBox Windows XP VM. I run both VIDA DICE and Toyota Techstream (for our Prius) on the VM with no problems. I actually just leave the VM always up and running so its like having my car diagnostic computer available all the time.

This said, VM does require a little more computer skills for setup. Probably about the same skill level to solve interference with other software installs. For someone with less computer skills, it seems a dedicate computer running Win XP is probably the easiest fool proof path.

Here is what I would do: Get VMWare Player (Free http://www.vmware.com/products/player/), which is a virtual machine software. VMWare Player does not allow you to create new virtual machines, just open previously made ones.

Next, find a Windows XP Professional VMWare image. This is more than just an install disk - this is a full already installed image of XP Professional SP3.

Open the XP image with VMWare Player, boot XP in your virtual machine, and install VIDA on that. You need to connect the USB DICE through to the Virtual Machine, see the help/tutorial to learn a little about VMWare player.

The huge advantage of this method is everything dealing with VIDA is completely isolated into that virtual machine. Thus you don't need to worry about what else you have installed that will mess up vida, viruses hidden in any of the SW you've acquired, etc. The only thing you are installing on your main PC is VMWare Player, which is very trustworthy.

You can even enter full-screen mode, which will make it seem like you are running the real XP.

The whole process should be very painless & simple, the only thing you are missing right now is a VMWare Image of XP Professional. If you want you can try installing XP from the installation disk you already have using VMWare Player, which requires a bit more work, see e.g.:http://johnbokma.com/mexit/2005/10/26/vmware-player-windows-xp.html .

-Colin

PS: VMWare Workstation (basically full version of player) is excellent SW, I've used it for many years now in a variety of environments. So I would have no hesitation using the player edition, but I honestly haven't tested the above with VMWare Player only. The Microsoft VM that comes with Windows 7 is a joke by comparison.

www.obd2france.com all rights reserved, Original Article url:How to install Volvo Vida/Dice on Windows XP VMWare Player

How to use ACTIA Multi diag I-2016 Win XP for Passat VII diagnosis

ACTIA Multi diag I-2016 update... Here you go.. About how to install and use Multi diag I-2016 software for vehicle obd2 diagnosis.

I-2016 actia multi diag price: €269

LOWER cost with actia multi diag I-2011 I-2014 I-2015

How to install ACTIA Multi diag I-2016:

CANNOT connect to the Internet when install the multi diag software

NO need actia multi diag keygen

NO need actia multi diag activation code

MUST use with actia passthru driver

How to use Multi diag I-2016 for diagnosis on Volkwagen Passat VII (2011-2016)

 

In the computer management

Select Device manager->I+ME ACTIA XS Device-> PassThur+ XS USB Driver

Select a car type: All systems- vag diagnostics

       

Multi-Diag I-2016 is tested to work no issues!

Actia multidiag works good at:

1. All maintenance and repair operations

- Reset maintenance indicators

- Read/Erase fault codes

- Read parameters (graphical representation)

- Test actuators

- Configure the calculator,

- Coding (Injectors, electronic tire valves...)

- Calibration and self-learning... Etc.

2. Diagnose the main vehicle systems: injection, ABS, ESP, Airbag, automatic transmission, air conditioning, central computer, dashboard, comfort systems, tire valves, immobilizer, direction, steering, etc…

3. Connected Services:

Connecter "Actiaconnect.com" to receive personalized information and access the many online services:

- Latest Updates Vehicles and Systems

- Online Help Topics

- Support requests directly by e-mail

- Remote control of your tool

- Accessories available to complete your Multi-Diag equipment

- Track your online subscription

- Technical and commercial information to fully exploit your diagnostic station

Multi-Diag I-2016 car list:

Covers more than 45 brands:

Alfa-Romeo, Audi, Autobianchi, BMW, Cadillac, Chevrolet, Chrysler, Citroën, Dacia, Daewoo, Daihatsu, Fiat, Ford, Honda, Hyundai, Jaguar, Kia, Lada, Lancia, Land Rover, Lexus, Maybach, Mazda, Mercedes, MG, Mini, Mitsubishi, Nissan, Opel, Peugeot, Porsche, Proton, Renault, Rover, Saab, Seat, Skoda, Smart, SSangyong, Subaru, Suzuki-Santana, Toyota, Volkswagen, Volvo, Zastava…

www.obd2france.com all rights reserved, Original Article url:How to use ACTIA Multi diag I-2016 Win XP for Passat VII diagnosis