BMW ICOM vs K+DCAN cable, which one you need?

What can you do with an BMW ICOM emulator, and which you cannot do with a K+DCAN cable? (especially in for E series) Here is something useful for education.

ICOM A2

K+Dcan cable

Diagram:

 

Price:

€469.00

€17.45

Vehicles:

New and old BMW vehicles:

E & F series up to 2017

Old BMW E series (1998 – 2008)

Software:

ISTA-D 4.04.12

ISTA-P 3.60.2.001

Inpa/Ediabas, Ncs expert, Winkfp, E-sys, ETK, Easyconnect, Itoolradar, BMW standard tool, coding database, coding tool

INPA/Ediabas

ICOM can be used with diagnosis and also programming. While DCAN cable can do all of those it is not safe to program modules because there have been a lot of cases where modules were bricked. You can only get your 1B file using FSC generator with ICOM on an E series car but cannot generate 1B file using a DCAN cable since it will give you an error. There is another way though of getting your 1B file without using an ICOM on an E series through the USB port inside your glovebox accessing the hard drive directly. Rather than going through all those stuff, it is more convenient to just buy the lifetime FSC code and be done with it.

To see if I understood:

Programming = Flashing a module, which means changing the actual software. Best done with an ICOM.

Coding = Reading and writing the memory which contains the configuration. Can be done with a K&DCAN cable.

ICOM: fast protocol, allows to secure flash software and read/write access the entire memory. Similar to JTAG programming.

K&DCAN Cable: slow serial protocol, flashing would take ages and errors could occur. Also, not possible to access the entire memory. Similar to RS232 bootloader access.

You program a module if you want to update the software to a newer one or if you a retrofitting a new module and want to flash it. ICOM is a lot more stable than dcan cable when it comes to programming. And you are right there are modules that takes hours to finish and any interruption in the process will surely brick that module. You can get a cheap china clone ICOM but finding a refutable vendor selling a good working ICOM is not easy. I’ve been using China ICOM from http://www.obd2france.com/wholesale/bmw-icom-a2-b-c-diagnostic-programme-appareil-avec-wifi-fonction.html it’s a good helper in my garage repair work. You can also get recommendations from others who bought a working clone ICOM.

www.obd2france.com all rights reserved, Original Article url:BMW ICOM vs K+DCAN cable, which one you need?

Where to download 04.2017 BMW ISTA 4.04.31 and ISTA-P 3.61.2?

You can free download here: 04.2017 BMW ISTA 4.04.31 Standalone and ISTA-P 3.61.2+ SQLiteDBs EN-GB V4.04.31 + Tool Check below mega links!

Free download BMW ISTA 4.04.31 Standalone with license (no VMware) + SQLiteDBs + Tool

https://mega.nz/#F!4Msz2RgL!jvZdlqN3SF75Z5rIRnWnYg!tZtkABRY

No pass!

Before unpacking do UNLOCK.

Use the latest WINRAR 5.11 and above to unpack.

Including Patched EDIABAS 7.3.0.msi, Net Framework 4.5.2, Net Framework 4.6.2, vcredist x64, vcredist x86, RCleaner V4.4.exe, vs90 piaredist.exe

Free download BMW ISTA-P psdzdata Lite V3.61.2

https://mega.nz/#F!tc00gSIb!QSJatG3d3e4JVaDMt2aIhw

No pass!

Note: BMW ISTA 4.04.31 is still with unknown security. So mates enjoy at your own risks!

If you want a 100% tested OK and safe ISTA, you can try 03.2017 BMW ISTA 4.04.12 WIN7 HDD.

BMW ISTA 4.04.31 and ISTA 4.04.12 compatible interface:

BMW ICOM A2

BMW ICOM A3

BMW ICOM Next

BMW K+DCAN cable

BMW ENET cable

Can I run BMW ISTA 4.04.31 on Windows 7?

Yes, check below:

BMW ISTA 4.04.31 Operating system:

Windows 7 (32-bit or 64-bit)

Windows 8 or 8.1 (32-bit or 64-bit)

Windows 10 (32-bit or 64-bit)

BMW ISTA 4.04.31 Hardware requirements:

Processor (CPU): min 2.2 GHz Dual Core or 4.4 GHz Single Core CPU (Summary of Cores or Threads should be more than 4.4 GHz)

Memory (RAM): min 4 GB

Hard drive (HDD): min 250 GB free space on disk C: before installation

How to install BMW ISTA 4.04.31? Any tips?

We first install the program itself via .msi, or we can base the base on the Standalone version. We unpack and add the database to the folder x: \ ISTA \ SQLiteDBs \.

Database files can be packed originally (.istapackage) or .rar.

To get a database from the .istapackage archive you need to change the extension to .rar and extract as usual. All databases in. \ SQLiteDBs directory should have a .sqlite extension.

The license to standalone is in a folder with RG.

www.obd2france.com all rights reserved, Original Article url:Where to download 04.2017 BMW ISTA 4.04.31 and ISTA-P 3.61.2?

Free download BMW ISTA Rheingold 4.04.12 ISTA-P 3.61.0 (mega)

Latest BMW ISTA update for sharing! Here are free download mega links for 03.2017 BMW Rheingold ISTA-D 4.04.12 Standalone + ISTA-P 3.61.0.500. Check below for more details:

You are going to download:

ISTA-D 4.04.12 + ISTA-P 3.61.0 (Expert Mode)

BMW ISTA 4.04.12 Standalone (native) installation with license, no VMware

It includes original ISTA+ programming SDP databases

BMW ISTA-P 3.61.0.500 Standalone installation with license (no VMware) + Expert Mode for single ECU programming

Note: Unknown security. Enjoy at your own risk!

Download Rheingold ISTA + 4.04.12 standalone version and language pack

https://mega.nz/#F!4Msz2RgL!jvZdlqN3SF75Z5rIRnWnYg!tZtkABRY

No password!

This link includes below software:

Rheingold ISTA+ Standalone V4.04.12

SQLiteDBs V4.04.12: 11.35GB

SQLiteDBs_Korea : v3.54.12

Tools (Net Framework+ vcredist+ patched EDIABAS V7.3.0.msi + RCleaner V4.4.exe + vs90 piaredist.exe)

Download BMW ISTA-P V3.61.0.500 Lite, BMW coding essential data psdzdata

https://mega.nz/#F!tc00gSIb!QSJatG3d3e4JVaDMt2aIhw

No password!

BMW ISTA 4.04.12 Interface requirements:

BMW ICOM A2

BMW ICOM A3

BMW ICOM Next

BMW K+DCAN cable

BMW ENET cable

Is there a tested safe and 100% working BMW ISTA with install tech support?

Yes!

BMW ISTA-D 4.02.12 ISTA-P 3.60.0.600 ICOM Software HDD with Engineers Programming for Windows 7

Not connected 9000 days remaining

With free BMW Engineer Software (INPA, NCS, WinKFP, E-Sys 3.27.1, Psdzdata 59.0), BMW FSC code generator and BMW AiCoder

Language: American English, British English, German, Spanish, French, Italian, polish, Portuguese, Turkish, Czech, Swedish, Indian, Greek, Russian, Simplified Chinese, Traditional Chinese, Japanese, Korean and Thai.

BMW ISTA 4.04.12 software information:

BMW ISTA+ 4.04.12 (other names are ISTA, ISTA-D or Rheingold)

Module (ECU) errors reading and clearing

Gearbox (transmission) and engine adaptations erasing

Fuel injectors control, correction amount real time viewing, injector registering

Engine mountings testing

Mass air flow (MAF) testing and registering. Whole air system testing

EGR system control and testing

Turbocharger and related components control and testing

Diesel particulate filter regeneration (DPF)

Battery replacement

Oil change and service interval reset

Wiring diagrams, live data, repair instructions, technical documents etc

Programming, vehicle retrofit, mirror coding, FSC codes adding or updating etc

And many more other functions

BMW ISTA-P 3.61.0.500 software information:

Battery type change

Module (ECU) software updating, coding and replacement

Vehicle retrofitting, options enabling and disabling

Choose ISTA-P language directly from ISTA-P taskbar agent

And many more other functions

BMW ISTA 4.04.12 software requirements:

Operating system

Windows 7 (32-bit or 64-bit)

Windows 8 or 8.1 (32-bit or 64-bit)

Windows 10 (32-bit or 64-bit)

Hardware requirements

Processor (CPU): min 2.2 GHz Dual Core or 4.4 GHz Single Core CPU (Summary of Cores or Threads should be more than 4.4 GHz)

Memory (RAM): min 4 GB

Hard drive (HDD): min 250 GB free space on disk C: before installation

It is from bmw icom francais technical support:Free download BMW ISTA Rheingold 4.04.12 ISTA-P 3.61.0 (mega)

BMW ICOM or K+Dcan cable to reset steering angle sensor

Here are two solutions of resetting BMW steering angle sensor, one using BMW ICOM ENET Toolset 32 for bmw F series, the other using INPA K+Dcan cable for bmw E series.

Why you need reset SAS?

The steering angle sensor (SAS) is a vital part of the ESC system that measures the steering wheel position angle and rate of turn.

When wheel alignment gets done or the actual physical direction the steering is set at, and the steering angle sensor’s last calibration is different enough to cause the DSC (dynamic stability control) ECU confusion in certain conditions.

Then you need to reset the steering angle sensor so that its straight ahead reading in software corresponds with the physical straight ahead position. 

---> For BMW F series cars:

Solution 1: bmw icom with Tool 32 reset steering angle sensor

Bmw 320d f30 2005

Bmw icom a2

Toolset 32

Well connected ENET cable or ICOM emulator with vehicle

Start launching Toolset 32 /Tool32:

Select “Load SGBD Group file”

Find your DSC module and click “open”, for example, a E90 2005 320D it is DSC_87.prg)

Drop down the “Jobs” list and find out “lenkwinkel dsc abgleichen” option, ignition on and double click the option. Wait for about 10 seconds until the job is finished.

The steering Angle is calibrated and VIN is matched to car.

---> For BMW E series:

Solution 2: K+DCAN usb cable with INPA reset steering angle sensor

Bmw e46

K+dcan cable

Inpa software

Well connect k+dcan cable

open INPA on the laptop

Select vehicle as E46
Select chassis
Select steering angle sensor

Hit F5 to read status

Hit F4 and the system will show the general status

You will able to view the current steering angle sensor is calibrated to close to zero deg. when the physical steering is pointed straight ahead

If the steering angle sensor calibration value is not extremely close or exact, you need to reset it.
Go to main menu and select E46 again
Select chassis
Select
DCS MK6

Click SHIFT+F4 buttons at the same, the system will display the compensation routines.

bmw icom a2+b+c diagnostic & programming tool

 
Avec un ordinateur portable

2016年12月22日星期四

Réinitialiser le capteur d'angle de direction BMW, Tool32 ou INPA?

Voici deux solutions de réinitialisation BMW capteur d'angle de braquage, un à l' aide de BMW ICOMENET Toolset 32 pour BMW Série F, l'autre en utilisant le câble INPA K + DCAN pour BMW Série E.

Pourquoi vous avez besoin de réinitialiser SAS?

Le capteur d'angle de braquage (SAS) est une partie essentielle du système ESC qui mesure l'angle de position du volant et la vitesse du tour.

Lorsque l'alignement des roues se fait ou la direction physique réelle de la direction est fixé à, et dernier étalonnage capteur de l'angle de braquage de est assez différent pour provoquer le DSC (contrôle dynamique de la stabilité) ECU confusion dans certaines conditions.

Ensuite, vous devez réinitialiser le capteur d'angle de braquage de sorte que son droit devant la lecture dans le logiciel correspond à la position droite physique.

-> Pour les voitures de série BMW F:

Solution 1: bmw icom avec outil de capteur d'angle de braquage de 32 réinitialisation

Bmw 320d f30 2005

Bmw icom a2

Toolset 32

Bien relié  par ENET cable ou émulateur ICOM avec le véhicule

Lancer le lancement Toolset 32 ​​/ Tool32:

Sélectionnez "Charger fichier SGBD Group"

Trouvez votre module DSC et cliquez sur "ouvrir", par exemple, un E90 2005 320D est DSC_87.prg)

Dérouler la liste "Jobs" et trouver l'option "lenkwinkel dsc abgleichen", contact et double-cliquez sur l'option. Attendez environ 10 secondes jusqu'à ce que le travail est terminé.

L'angle de braquage est calibré et VIN est adapté à la voiture.

-> Pour BMW Série E:

Solution 2: câble usb K + DCAN avec capteur d'angle de braquage de remise à zéro INPA

bmw e46

K+dcan cable

Inpa software

Bien connecter k + câble DCAN

ouvert INPA sur l'ordinateur portable

Choisir véhicule E46
Choisir châssis
capteur d'angle Select de direction

Hit F5 pour lire l' état

Hit F4 et le système affiche l'état général

Vous sera en mesure d'afficher le capteur d'angle de braquage actuel est calibré à près de deg zéro.lorsque la direction physique est pointée droit devant

Si la valeur d'étalonnage du capteur d'angle de braquage est pas très proche ou exacte, vous devez le réinitialiser.
Aller au menu principal et sélectionnez E46 nouveau
Sélectionnez châssis
Sélectionnez
DCS MK6

Cliquez SHIFT + touches F4 au même, le système affiche les routines de compensation.

Click F1 button to reset the steering angle sensor

Go back to steering angle sensor menu to view the current status. The calibrated value should go down to zero. The procedure is complete and then you can clear the error codes or do other coding options.

Enjoy!

Free download BMW ICOM Rheingold ISTA 4.03.13 (Torrent)

In this blog obd2france.com offer you free download link of newest BMW Rheingold ISTA+ 4.03.13 Standalone / SDP 4.02.31 / ISTA-P 3.60.2.001! Also ISTA 4.02.14 link is here. Mates enjoy but also try on your own risk!

Free download BMW ISTA+ 4.03.13 Standalone / SDP 4.02.31 / ISTA-P 3.60.2.001:

https://mega.nz/#!UkokgQhC!Vpviwwre4R32W0oVDsIl5Wt0-bTuo7Y8qOHXz3FCGXU

BMW ISTA 4.03.13 software package list:

Free download BMW ISTA-D Rheingold 4.02.14 Standalone / SDP 4.02.13 / ISTA-P 3.60.0.600

https://mega.nz/#!1lYRyYCa!s734Z8ilpoeLkyPaxQCUMb2NHZ2yTXqhp-Kgd4-B9JE

BMW ISTA-D Rheingold 4.03.13+ ISTA-P 3.60.2.001 required interfaces:

BMW ICOM A2

BMW ICOM A3

BMW ICOM Next

BMW INPA K+DCAN USB interface

BMW ENET cable

Software details of BMW ISTA Rheingold 4.03.13:

Module (ECU) errors reading and clearing

Gearbox (transmission) and engine adaptations erasing

Fuel injectors control, correction amount real time viewing, injector registering

Engine mountings testing

Mass air flow (MAF) testing and registering. Whole air system testing

EGR system control and testing

Turbocharger and related components control and testing

Diesel particulate filter regeneration (DPF)

Battery replacement

Oil change and service interval reset

Wiring diagrams, live data, repair instructions, technical documents etc

Programming, vehicle retrofit, mirror coding, FSC codes adding or updating etc

And many more other functions

Before install BMW ISTA+ Rheingold 4.03.31, need Install:

Ediabas 7.3.0, Java, vcredist 2005-2015, vs90_piaredist, net framework 4.5.2 and 4.6.2

If the system is x64, vcredist must install and x86 and x64, otherwise start Rheingold.

All except Java and net framework 3.5 is in the Tools folder.

Operating system:

Windows 7 (32-bit or 64-bit)

Windows 8 or 8.1 (32-bit or 64-bit)

Windows 10 (32-bit or 64-bit)

Original - from obd2france.com obd2 francais:Free download BMW ICOM Rheingold ISTA 4.03.13 (Torrent)

How to rework ICOM A2 with heatsink for Cooling chips

This is a great solution of ICOM A2 reworkwith a heatsink which is cooling both chips.

(GREAT THANKS to B1257)

Now here are some pictures about the heatsink I made.

Picture1 As you can see in my way the heatsink is made with two parts. The main center plate which will later touch the complete case for a better heat dissipation. And second the small CPU plate which is glued with a special Thermal Bound paste for FPGA chips on the center plate. You can see the compound type on the picture.

Picture2 Shows the Temp in C° after an idle running time of the head about 30 minutes, without any cooling.

Picture3 Original there are two pads for the cooling, but not one is touching the case, after a longer time the complete case will warm up in a way that the both chips are near out of max temp range, which is in a normal grade about 70°C. For our heatsink I will use a small pad for the MICREL chip to give me the right contact to my center plate. Second reason is that the pad gives me a little bit place for a realignment to center the main plate with both chips.

Picture4 You can see new srewls and bolts to compensate the new height. The screwls dimension of the innerside srewls is 2.5x12mm (countersunk bolt, this is important, because we cant fix the center place in the case if there is not enough place with normal screwls.)

Picture5 Be careful to center the plate exactly with vary the three plastic bolts, may you have to cut it a little bit. Check the space between the case and the center plate one or more times. Take care that both chips are touching the heatsink, because some cases can vary the height.

Picture6 Apply compound paste to the center plate, where the heatsink is later touching the case for the best heat dissipation.

Picture7 For the best way take care that the complete heatsink is touching the case. See the red arrow.

After the heatsink mod the temps are always inside the specs. I remember 5 hours idle running about 40.5C° room temp about 26°C.

Attachment:

Heatsink Dimension PDF overview

https://mega.nz/#!C88F2LjL!rVms_i_EzXJHLw8H9KlWUrNAz6Q_iqb0-XqMlZEYCyM

Sketup File

https://mega.nz/#!TsMDBJ6J!swzuKD5_4TnTrVhzjiEqrwTWcV5yDp5mu0wYwnpZm84

I hope this helps you to mount the heatsink in a proper way.

So advice to all -

To avoid issues, please check the PCB design (with the cooling plate) before your buying. when buying from China, it seems obd2france.com is one of the safest way to make sure of things quality.

This is their ICOM A2 pcb with a cooling plate

(BIG THANKS to B1257 in http://cartechnology.co.uk/)

Original - from obd2france.com obd2 francais service technique:How to rework ICOM A2 with heatsink for Cooling chips

Rapporter l'article:

bmw icom francais